Restoration

Efflorescence on Brick and Stucco: What It Tells You in BC

November 18, 2026 · 9 min read

White powder on a brick or stucco wall is salt carried out by water. Where it shows up tells you where the water gets in, and whether the wall needs repair.

New white and grey brick veneer on a Metro Vancouver multi-unit build, the kind of fresh masonry where efflorescence first appears in BC

Every March, after five months of rain, owners across Metro Vancouver walk outside and find a white chalky bloom on their brick. It may be a soft haze over a whole new wall, or one sharp stripe under a single window, or a band along the bottom of the stucco that comes back no matter how often someone scrubs it. Efflorescence on brick in BC is common enough that most people shrug at it. The white staining is harmless in itself. Its location is the useful part, because it marks where water has been moving through the wall.

What causes efflorescence on brick and stucco?

Efflorescence is salt left on the surface after water evaporates. Brick, mortar, concrete and cement stucco all contain soluble salts. When water soaks into the wall, it dissolves those salts and carries them outward. At the face the water dries off and the salt stays behind as white powder. It needs three things at once: salts in the material, water moving through it, and a surface where that water can evaporate. Take away the water and the efflorescence stops.

New-building bloom and the white staining that comes back

There are two kinds, and telling them apart is the first job on any site visit.

Primary efflorescence shows up in the first year or two after brick or stucco goes on. The mixing water in fresh mortar and stucco carries salts out as the wall cures, and a new wall can turn grey-white within weeks of its first heavy rain. It tends to be even across a whole elevation. It washes off, it comes back weaker each season, and after one or two winters it is mostly gone. Builders call it new-building bloom. On a house finished in 2025, a uniform haze across the brick in its first spring is close to normal.

Secondary efflorescence appears on a wall that has been clean for years, or it returns to the same spot every winter. The salts from construction washed out long ago. Something has started feeding the wall a steady supply of water, and the water is pulling salt from deeper in the brick, the mortar, the stucco or the soil behind it.

A wall that blooms evenly in its first spring is better news than an older wall with one white stripe under one window. The stripe is the one that tells you about a leak.

What the location tells you

Efflorescence draws a map of where the water travels. These are the patterns we see most often on BC houses and low-rise strata buildings:

  • A fan or stripe under a window. Water is getting in at the sill: a sill with no drip edge, a sill flashing that ends short of the jamb, or a sealant joint that opened up years ago. It runs down inside the brick or stucco and dries out below.
  • A band along the bottom 300 to 600 mm of the wall. Water is wicking up from the ground or splashing back from a hard surface. On stucco this often means the finish runs into the soil or onto the foundation with no clearance. Our article on stucco weep screed and lath explains why that bottom edge matters so much.
  • White lines that follow the mortar joints. The joints are carrying the water. Mortar on a 1960s brick bungalow in Burnaby or a 1912 walk-up in Mount Pleasant is often eroded, cracked or too hard for the brick around it. That points to brick repointing and mortar repair.
  • Staining that starts below a cap, coping or chimney crown. The top of the wall is open. A cracked chimney crown or a coping with no drip lets water straight down into the core of the masonry.
  • A hard white run from a crack, sometimes with drip-shaped edges. This is lime from the mortar or stucco, carried out and hardened into calcium carbonate. A run that thick tells you water has been flowing through that crack for years.
  • A patch on the wall below a deck, balcony or planter. The membrane or the flashing at the ledger is leaking into the wall.

A lawn sprinkler that hits the same brick wall every summer evening will put white rings on it within a season. Before anyone opens a wall, walk the garden while the irrigation runs.

Is it efflorescence, mould, or something else?

Try three tests on a dry day. Put a drop of water on the white deposit: efflorescence softens or dissolves. Put a drop of household vinegar on it: if it fizzes, you are looking at calcium carbonate from lime, which water will not shift. Then rub it between your fingers. Salt feels gritty or powdery. Mould smears, looks fuzzy up close, and spreads in blotches rather than following joints or drip lines.

Grey or black staining with white efflorescence around it on stucco is a different conversation. That combination usually means the wall behind is wet enough to grow mould, and probe readings are the next step. Our piece on testing stucco for moisture covers what those readings mean.

When the salt starts doing damage

On the surface, efflorescence is cosmetic. The trouble starts when the salt crystallises inside the material, just behind the face. That is called subflorescence, and the growing crystals push outward. Brick faces flake off in thin layers. Stucco finish coats lose their bond and sound hollow when tapped. Paint and elastomeric coatings blister and peel in patches.

BC adds freeze-thaw to that. Most of Metro Vancouver gets only a handful of hard frosts each winter, but a wall that stays saturated from November to March is exactly the wall that spalls when the temperature drops below zero. In Abbotsford, Chilliwack and the North Shore uplands the frost days add up faster. Spalled brick and delaminated stucco are where a cleaning job turns into a repair.

Cleaning efflorescence without making the wall worse

Owners often do more harm removing the white staining than the efflorescence did. In order:

  1. Brush it off dry. A stiff nylon brush on a dry day removes most fresh efflorescence. Do not use a wire brush on brick or stucco: the steel bristles leave fragments that rust into orange streaks.
  2. Rinse lightly, if at all. A wet rag or a low-pressure rinse is enough. Soaking the wall dissolves the salt and pulls it straight back in, so the bloom returns within a week.
  3. Leave the pressure washer in the garage. High pressure drives water deep into brick and mortar, opens weak joints, and forces water behind stucco.
  4. Use acid only with care. Hard calcium carbonate deposits sometimes need a masonry cleaner. On light-coloured brick, a strong acid can leave green or brown stains that are harder to remove than the salt, and on coloured stucco it can bleach the finish. Use a product the brick maker approves, test a small hidden area first, and wet the wall before the cleaner goes on.

A clear water repellent can help once the leak is fixed and the wall has dried for a full season. A sealer applied over a wet, salty wall traps the salts under the surface and turns surface bloom into subflorescence. That is how a cosmetic problem becomes spalled brick in two winters.

What the repair costs

Cleaning the white staining off one elevation of a house, with ladders or a small lift, typically runs $400 to $2,000, mostly for access. It fixes nothing if the efflorescence is secondary.

The repair follows the source. A new sill flashing or a sealant joint at one window on a brick house usually costs $600 to $2,500. Repointing mortar joints runs $15 to $40 per square foot in BC. A chimney crown rebuild or a coping replacement is often in the low thousands. Correcting the base of a stucco wall where it meets the ground costs more, because the bottom of the stucco has to be cut back, the weep screed installed and the finish patched and colour-matched: plan on $40 to $90 per linear foot on a house, more where sheathing behind it has rotted.

Our masonry repair crews handle brick, mortar and caps, and our stucco and EIFS team handles base details and patching, so the source and the finish get fixed together.

Insurance and warranty

Home insurance in BC does not pay to clean efflorescence. It is gradual and cosmetic, and most policies exclude gradual seepage and wear. The exception is resulting damage: if a sudden event such as a storm or a burst pipe soaks a wall and the staining follows, ask your broker before you assume it is excluded. Photograph the wall with dates.

On a house under ten years old, BC's 2-5-10 home warranty includes five years of building envelope coverage. Warranty providers usually treat surface efflorescence on new brick as a normal characteristic of masonry. A recurring stripe under a window on a three-year-old house is a sign of water penetration, and that water penetration is what the claim is about. Report it in writing inside the coverage period.

On a strata building, brick and stucco walls are common property. Report the pattern to the property manager with photos. If it appears on several units at the same detail, the building envelope consultant should see it before the next budget.

What happens when

First 24 hours. Efflorescence is not an emergency. Take photos with a date and a tape measure for scale, mark the area, and check gutters, downspouts and sprinklers near the wall. Do not pressure wash, seal, or paint over it.

First week. A site visit in dry weather. We map where the efflorescence sits, take moisture readings at and around it, and run a hose test at the suspected entry point with someone watching the far side. If readings are high, a small inspection opening goes in, and the written scope follows from what it shows.

Full repair. Cleaning takes a day. A window sill or cap repair takes one to three days. Repointing an elevation takes one to two weeks, and a stucco base correction along a full house takes one to three weeks. Mortar and stucco need temperatures above 5°C to cure, so from December to February some of this work waits for a dry spell or goes under heated enclosures. The efflorescence fades over the following year as the wall dries.

Who should look at the wall

MV Construction has repaired brick, stone and stucco walls across Greater Vancouver and Vancouver Island for 17+ years. We are fully licensed and WCB-insured, our crews take emergency calls 24/7 within Greater Vancouver, and our masonry and stucco repairs carry a written warranty.

If white staining keeps coming back on your brick or stucco, call (778) 375-5672 or request a free written estimate. We find the water source before we price the repair, and the scope, price and timeline are in writing before work begins.

Planning the work this guide covers?

Fixed scope, same-day reply. Tell us about the building and we'll take it from there.