Cut a 300 mm strip off the bottom of a 1990s stucco wall in Surrey or Richmond and you will often find the same thing. The stucco runs straight past the wood framing and onto the concrete foundation, bonded to it in one piece. There is no stucco weep screed at the base, or there is one buried under 150 mm of bark mulch from a garden bed someone added later. Behind it the sill plate is dark, and soft enough to take a screwdriver. The wire lath has rusted into a brown lace that comes away in your hand.
Everyone involved did their visible job well. The owner picked a colour and a texture, the plasterer finished the wall to a crisp line, and the landscaper made the beds look good. The trouble sits in two hidden parts nobody looks at once the finish coat goes on: the weep screed along the bottom edge, and the lath that holds the stucco to the building. On a BC wall, those two parts decide whether stucco lasts 50 years or 15.
What does a stucco weep screed do?
A stucco weep screed is the metal or vinyl trim along the bottom edge of a stucco wall. It stops the stucco in a straight line above the foundation, keeps it off concrete and soil, and lets water running down the building paper drain out through its slots. In BC it sits at or just below the joint between foundation and sill plate, with the paper lapped over its flange and 200 mm clear of finished ground.
Lath is the other hidden part. It is the steel mesh fastened through the paper into the studs, and the first coat of stucco is pushed through it so the wire ends up buried inside the cement. The lath carries the weight of the finish, roughly 40 kg per square metre at the usual 19 to 22 mm of three-coat stucco, and keeps it attached as the building moves and dries.
Stucco holds water, so the base has to drain
Cement stucco is a reservoir cladding. It soaks up rain, holds it, and dries back out over the following days. On a west-facing wall in Metro Vancouver between October and April there are few drying days, and part of that water keeps moving inward. More gets in at cracks, at window corners, and wherever a hose bib, dryer vent or deck ledger passes through the wall.
So every stucco wall is designed on the assumption that some water will reach the back of the stucco. What happens next depends on the drainage layer behind it.
On a face-sealed wall, the stucco sits directly on two layers of building paper. The two layers are there for a reason few owners hear about. Wet stucco bonds to the outer layer as it cures, and that layer wrinkles and sticks. The inner layer stays free. It becomes the drainage path, and the wrinkles act as small channels down the wall. A wall built with a single layer has its stucco glued to the only barrier it has.
On a rainscreen wall, a cavity of vertical strapping, 10 to 19 mm deep, separates the paper on the sheathing from the back of the stucco. Water that crosses the stucco falls down an open gap, and air moving through the cavity dries the wall. Under the current BC Building Code, new wood-frame houses in most of Metro Vancouver are built this way. A large share of the stucco houses and low-rise strata buildings put up in the 1980s and 1990s are face-sealed, and those are the walls we open most often.
Either way, the water runs down by gravity until it reaches the bottom of the wall. The weep screed is the planned exit. Without one, the water stops where the stucco meets the concrete. That joint sits level with the sill plate, the lowest piece of wood in the wall and the first one to rot.
The hidden parts of a stucco wall, from the studs out
A three-coat stucco wall on wood framing in BC is built up in this order:
- Studs and sheathing, plywood or OSB.
- Water-resistive barrier: two layers of building paper, or a housewrap with a paper layer over it.
- On rainscreen walls only: vertical strapping, then a backing layer that keeps stucco out of the cavity.
- Lath, fastened through everything into the studs.
- Scratch coat, about 10 mm, pushed through the lath and scored so the next coat grips.
- Brown coat, about 10 mm, straightened and floated.
- Finish coat, 2 to 3 mm, the colour and texture.
Around the edges sit the accessories: the weep screed at the base, casing bead around windows and doors, corner bead on outside corners, control joints that break big panels into smaller ones, and drip flashing at window heads and floor lines.
Owners spend most of their decision time on item 7. It is the part least likely to decide how long the wall lasts. A finish coat can be redone over a sound wall for $5 to $10 per square foot. Items 2 through 4 and the screed can only be fixed by tearing the stucco off.
Getting the stucco weep screed right
Height and laps
The screed's attachment flange is nailed to the framing at the bottom of the wall, so its nose sits at or just below the line where the sill plate meets the foundation. The nose projects past the face of the concrete, which lets water drip clear of the foundation instead of running down it and wicking back into the joint. Most screeds sold in BC follow the American profile with an attachment flange of at least 89 mm, tall enough to cover the plate joint with room to spare.
The laps are where most installations go wrong. The building paper has to come down over the outside of the screed's flange, shingle style, so water running down the paper lands on the outer face of the screed and leaves through the weep slots. When the paper is tucked behind the flange, water runs down the back of the screed straight onto the sill plate. From the outside the two versions look the same. The only way to know is to see the base before the scratch coat goes on, or to cut a small inspection opening later.
Clearance to the ground
Part 9 of the BC Building Code, in section 9.28 on stucco, asks for stucco to stop at least 200 mm above finished ground unless it is applied over concrete or masonry. Many screed packages print 100 mm to soil and 50 mm to paving. Those numbers come from US codes. On a BC house, keep 200 mm, and count bark mulch, gravel and pavers as finished ground, because they block the weep slots as well as soil does.
Grade creeps. A garden bed gets topped up every spring, a patio gets a second layer of pavers, a hot tub pad goes in against the wall. Ten years after the stucco went on, the screed that started at 200 mm is underground.
Material
| Screed material | Where it works | What to watch |
|---|---|---|
| Galvanized steel | Sheltered and inland sites | Rusts at cut ends and scratches; near salt water it can rust through long before the stucco is due |
| Vinyl (PVC) | Most residential walls, including coastal | No rust; can crack if hit in cold weather; needs a stiff profile so long runs stay straight |
| Zinc alloy or stainless steel | Waterfront homes in White Rock, Steveston or Tsawwassen, and commercial work | Several times the price of galvanized |
| Aluminum | Not used with cement stucco | Wet Portland cement is alkaline and corrodes aluminum |
Rainscreen walls
On a rainscreen wall the base detail changes. The cavity behind the stucco has to stay open at the bottom so water drains and air moves, which means a perforated vent strip or insect screen across the bottom of the cavity and a flashing that kicks water out past the foundation. The stucco stops on its own screed or drip edge in front of that.
The mistake we find most here is the bottom of the cavity packed with stucco that fell behind the lath during the scratch coat. A clean cavity drains. A cavity with 50 mm of hardened droppings at the bottom holds water against the sheathing like a gutter with the downspout plugged.
Floor lines and window heads
The same drainage job repeats higher up. A two- or three-storey wood-frame building shrinks as the framing dries, roughly 6 to 12 mm per floor, most of it across the rim joists and plates. Stucco run straight across a floor line in one plane cracks along that line within a few years. The original design should have a horizontal joint at each floor line, a drip screed or two-piece expansion joint with flashing behind it, so the wall can close up as the wood shrinks and the water collected above can drain out. Window heads, the top of a deck ledger and the underside of a soffit need the same kind of drip edge.
Lath: the part that holds the stucco on
Two kinds of lath carry most BC stucco. Woven wire, usually called stucco wire, comes in rolls, typically 17-gauge wire in 38 mm hexagons, and is often sold paper-backed so the lath and the outer paper go up together. Expanded metal lath is a sheet of steel slit and stretched into a diamond mesh, sold in 686 by 2,438 mm sheets. It is stiffer and the usual choice on commercial walls.
Either kind has to stand off the paper by about 6 mm. Self-furring lath does this with dimples or crimps formed into the mesh. The gap lets the scratch coat push through the wire and close up behind it, so the steel ends up fully inside the cement. Lath laid flat against the paper gets stucco on one side only. The bond is weaker, and the steel stays exposed to whatever water reaches the back of the stucco.
Fastening matters as much. Lath should go through the sheathing into the studs, every 150 to 180 mm down each stud, with galvanized nails or staples, and be lapped and tied at the sides and ends of every sheet or roll. Staples driven only into plywood or OSB between studs hold while the sheathing is dry. Once the sheathing gets wet and softens, they pull out, and the stucco bulges between the stud lines.
Then there is rust. Lath is galvanized, and in a wall that dries out between storms the zinc coating lasts as long as the stucco does. In a wall that stays wet at the base or under a leaking window, the zinc goes first and the steel follows. Rust takes up several times the volume of the steel it came from, so a corroding lath swells inside the scratch coat and pushes the stucco off the wall from within. It is the same rust jacking that spalls concrete balconies over corroded rebar.
Stucco lath in trouble leaves marks you can read from the ground:
- Horizontal cracks at a regular spacing, often close to 686 mm apart, which is the height of an expanded metal sheet and so the line of the laps.
- Vertical cracks about 400 mm apart, matching stud spacing, where fasteners are pulling or rusting.
- Brown or orange stains bleeding out of cracks or along the base of the wall.
- A hollow, drummy sound when you tap the wall with a screwdriver handle.
- A bulge you can see by sighting along the wall in low sun.
Patching a crack over rusted lath fixes nothing. The patch looks fine for a winter and opens again on the same line the next fall, because the steel behind it is still growing.
Checking your own wall from the ground
You can do most of a first inspection with a tape measure and a flashlight on a dry afternoon.
- Walk the base of every elevation. Look for a straight metal or vinyl edge with a small projecting nose. If the stucco runs down onto the concrete with no line between them, there is no weep screed.
- Measure from the bottom of the stucco to the soil, mulch or paving. Note every spot under 200 mm, and every spot where the ground slopes toward the wall.
- Look under the nose of the screed. You should see a gap or slots. Caulk, paint or stucco bridging the gap to the foundation means the weep is closed.
- Check the base and the window corners for rust stains and white crusty deposits.
- Look for cracks at regular spacing, horizontal or vertical, and tap any you find.
- Inside, look at the bottom of drywall and baseboards on exterior walls, especially below windows, for stains, swelling or a musty smell.
None of this tells you how wet the sheathing is. For that the wall needs probe readings, and our guide to stucco moisture testing in BC explains how a survey is done and what the numbers mean.
Mistakes we see on BC stucco walls
The most expensive one is the reverse lap at the screed, with the paper tucked behind the flange. It is invisible once the scratch coat is on, it sends water straight to the plate, and it cannot be corrected without cutting the base off.
The most common one is a closed weep. A painter runs a bead of caulk under the screed nose to give the base a finished edge, or the plasterer lets stucco bridge from the screed to the concrete. Either one turns a drain into a dam.
Raised grade comes next: new patios, planters, rubber mulch and hot tub pads against the wall. On strata buildings it is usually a patio upgrade by an owner.
Then patching over the cause. Cracks along lath laps get filled and painted, rust stains get primed and coated, and the wall looks right for a season. On waterfront sites, galvanized screed and lath rust first and take the stucco with them, which is why we specify vinyl or zinc within sight of salt water.
What base and lath repairs cost in BC in 2026
| Work | What it involves | Typical 2026 cost, Metro Vancouver |
|---|---|---|
| Clearing the base | Pull soil or mulch back to 200 mm, cut caulk and stucco out of the screed, reopen the weep slots | $300 to $1,500; $2,000 to $6,000 when pavers or a patio edge have to be cut back and regraded |
| Base-of-wall repair | Cut off a 300 to 450 mm band, inspect plate and sheathing, new paper lapped over a new screed, new lath, three coats | $110 to $220 per linear foot, about $4,400 to $8,800 on a 40-foot elevation |
| Rot repair behind the base | Replace sections of sill plate and sheathing, sometimes stud ends | Adds $1,500 to $6,000 per elevation |
| Finish coat to blend the repair | New colour coat over the whole elevation so the patch line disappears | $5 to $10 per square foot of wall |
| Lath failed across an elevation | Tear off to the sheathing, rebuild with a rainscreen cavity | $28 to $42 per square foot residential, $35 to $55 on strata with engineering and access |
A cut band of new stucco never matches the old colour exactly, so most owners pair a base repair with a finish coat over the elevation. Budget for both together.
The base repair is also where a written estimate earns its keep. Nobody knows what the sill plate looks like until the stucco is off. A good estimate prices the band repair as a fixed line and the rot repair as unit rates, per linear foot of plate and per sheet of sheathing, so a soft plate adds a known amount. Our article on change orders for hidden conditions covers how those unit rates should be written.
Choosing between those rows comes down to what the wall shows. A buried or blocked weep screed with probe readings at the base under about 19 percent needs clearing and a winter of watching. A missing or reverse-lapped screed with a soft plate needs the base repair on the affected elevations. Rust stains and lap-line cracks across most of an elevation mean the lath is gone, and patching that wall is money spent twice: re-clad it with a rainscreen.
Strata buildings: the base of the wall is common property
On a strata building the bottom metre of stucco is where the wall meets the ground-floor patios. The exterior of the wall is common property under most BC strata plans, while the planters, pavers and hot tub pads that bury the screed were usually put there by owners. A walk around the building before each AGM, with a tape measure at every ground-level patio, costs nothing and catches the problem while it is still a landscaping fix.
When a council does fund base repairs, doing every affected elevation in one contract costs less per foot than chasing units one at a time. Mobilization, access and colour matching get paid for once, and the whole base gets the same detail. On larger buildings the base of the stucco is usually part of a wider building envelope repair scope, and it is worth asking the envelope consultant to include the screed and lath condition in their report.
Our recommendation
On a new wall or a re-clad, put your attention on the hidden parts. Specify vinyl or zinc screed anywhere near salt water, and galvanized only on sheltered inland sites. Have the paper lapped over the screed flange, choose self-furring lath fastened into the studs, and ask your contractor to show you the base before the scratch coat covers it. On a rainscreen wall, ask how the bottom of the cavity will be kept clear.
On an existing wall, start with a tape measure. Fix the grade before you fix anything else, because a buried weep screed undoes every other repair. If you find rust lines or cracks at a regular spacing, get the wall probed before anyone prices a patch.
MV Construction has built and repaired stucco across the Lower Mainland and Vancouver Island for 17+ years. We are fully licensed, WCB-covered and insured, and the work carries our warranty. Every project starts with a free written estimate, so the screed, the lath and the paper are in writing before work begins. The systems we install are on our stucco and EIFS contractor page.
FAQ
Is a weep screed required on stucco in BC? The BC Building Code requires stucco to stay 200 mm clear of finished ground and requires wall assemblies to drain water that gets behind the cladding. On a framed stucco wall, the weep screed or a perforated base flashing is how that drainage is built, and the lath and stucco installation standards used in BC specifications call for one at the base of every exterior framed wall.
Can a weep screed be added to existing stucco? Yes. The crew cuts off a band of stucco at the base, usually 300 to 450 mm high, checks the sill plate and sheathing, and rebuilds the band with new paper lapped over a new screed, new lath and three coats. In 2026 that runs about $110 to $220 per linear foot in Metro Vancouver, plus rot repair if the plate is soft and a finish coat to blend the colour.
How long does stucco lath last? In a wall that dries out between storms, galvanized lath lasts as long as the stucco, 50 years or more. In a wall that stays wet at the base or under a leaking window, the zinc coating goes first and the steel can rust through in 15 to 25 years. Regular horizontal cracks and rust stains are the usual signs.
How high should stucco be above the ground in BC? At least 200 mm above finished ground under section 9.28 of the BC Building Code, unless the stucco is applied over concrete or masonry. Soil, bark mulch, gravel and pavers all count as ground. The 100 mm to soil and 50 mm to paving printed on many screed packages come from US codes and are lower than the BC figure.
If your stucco runs straight down onto the foundation, or you have rust lines on the wall you cannot explain, call (778) 375-5672 or request a written estimate. We will look at the base, take readings where they are needed, and put the repair in writing before anything is cut.



